NEWS
You are here: Home » News » How to make better use of the production benefits of laser engraving machine

How to make better use of the production benefits of laser engraving machine

Views: 0     Author: Site Editor     Publish Time: 2021-12-28      Origin: Site

For safety protection and efficient production, the most important thing is the daily safety maintenance and maintenance of the equipment; if done, not only can the service life of the machine be prolonged, but also the quality of the two-dimensional code engraving can be maintained and improved, and finally stable High efficiency. Please do the following matters earnestly:

  1, good grounding

  The laser power supply and the machine bed body must have good grounding protection, and the ground wire should be a special ground wire less than 4ω. The necessity lies in: (1) to ensure the normal operation of the laser power supply, (2) to prolong the service life of the laser tube, (3) to prevent the machine jitter caused by external interference, and (4) to prevent accidental circuit damage caused by high-voltage discharge. Good grounding, be sure!

  2, the cooling water should be unblocked

   Whether using tap water or a circulating water pump, the water must be kept flowing smoothly. The cooling water takes away the heat generated by the laser tube. The higher the water temperature, the lower the light output power (15-20℃ water temperature is better); when the water is cut off, the tube end will burst due to the heat in the laser cavity and even damage the laser power supply. Therefore, it is necessary to check whether the cooling water is unblocked at any time. When the water pipe has a hard bend (dead bend) or falls off, and the water pump fails, it must be repaired in time to avoid power drop or even equipment damage.

  3, clean and maintain, good ventilation, wipe at any time

  The cleaning and maintenance of the machine tool is a necessary condition for the normal operation of the machine tool. Imagine that people's joints are not flexible, how can they act? In the same way, the machine tool guide rail is a high-precision core component. After each work is completed, it must be wiped clean to keep it smooth and lubricated; each bearing must also be oiled regularly, so that the drive is flexible, the QR code engraving and processing are accurate, and the use of the laser engraving machine is extended. life.

   4. Ambient temperature and humidity

   The ambient temperature should be in the range of 5-35°C. Special attention should be paid to: if it is used in an environment below freezing point, it must be: (1) to prevent the circulating water in the laser tube from freezing, and the water must be completely discharged after shutdown; (2) the laser current must be preheated for 5 minutes when it is turned on The above can only work. In rainy days and humid environments, the laser power supply needs a longer warm-up time, and the high voltage can be added after the moisture is exhausted to prevent the high-voltage circuit from breakdown.

   5. Use the "Laser High Voltage" button correctly

When the   "Laser High Voltage" key is dialed in, the laser power supply is on standby. When it encounters "manual light output" or computer misoperation, it will emit laser light, inadvertently hurting people and objects. Therefore, it is required that the "laser high voltage" should be turned off at any time if the work is not continuous, (laser current can be turned off), and the operator is prohibited from leaving without authorization when the machine is working to avoid accidents. It is recommended that the continuous working time be less than 5 hours, 30 minutes rest in between.

   6. Keep away from equipment with high power and strong vibration

   Sudden interference from large power can sometimes cause the machine to malfunction. Although it is rare, it should be avoided as much as possible. Therefore, large electric welding machines, giant electric mixers, and large power transmission and transformation equipment should be kept away. Strong vibration equipment is even more self-evident, such as forging presses, vibrations caused by short-distance motor vehicles, etc., the obvious shaking of the ground is very detrimental to accurate two-dimensional code engraving.

  7, lightning protection

   As long as the building's lightning protection measures are reliable. The first article of the article "good grounding" can also help prevent lightning.

   Special recommendation: In areas with unstable network power (such as voltage fluctuations of more than 5%), please install a regulated power supply with a capacity of at least 3000w to prevent sudden voltage fluctuations from burning the circuit or computer.

   8. Maintain and control the stability of PC.

  Control pc is mainly used for engraving equipment control. In addition to installing the necessary graphic design software, please do not use the special plane.

   After the computer is installed with a network card and anti-virus firewall, it will seriously affect the speed of the control machine. Please do not install an anti-virus firewall on the control machine. If you need a network card for data communication, please disable the network card before starting the laser engraving machine.

9. Maintenance of the guide rail: During the movement of the guide rail, a large amount of dust will be generated due to the processed material. Maintenance method: first wipe off the original lubricating oil and dust on the guide rail with a cotton cloth, and then apply a layer of lubricating oil on the surface and side of the guide rail. Maintenance period: about one week.

  10. Maintenance of the fan: After the fan has been working for a period of time, a large amount of dust will accumulate in the fan and exhaust pipe. The dust will affect the exhaust efficiency of the fan and cause a large amount of smoke and dust to be unable to be discharged. Maintenance method: loosen the hose clamp connecting the exhaust pipe and the fan, remove the exhaust pipe, and clean the dust in the exhaust pipe and the fan. Maintenance period: about one month.

  11. Fastening of screws: After the motion system works for a certain period of time, the screws at the motion connection will loosen, and the loosening of the screws will affect the stability of the mechanical motion. Maintenance method: Tighten the screws one by one with the tools provided with the machine. Maintenance period: about one month.

   12. Maintenance of the lens: After the machine has been working for a period of time, the lens will stick a layer of dust on the surface due to the working environment, which will reduce the reflectivity of the reflective lens and the transmittance of the lens, and ultimately affect the working power of the laser. Maintenance method: Use absorbent cotton dipped in ethanol to gently wipe the surface of the lens in a clockwise direction to remove dust.


Contacts
​​​​​​​​​​​​​​Tel:+86 186 6040 2807 
Email:info@siemelaser.com 
No.12111 Jingshi Road,Lixia District,Jinan city,Shandong,China
Social websites
© Copyright  JINAN SIEME CNC EQUIPMENT CO.,LTD